Arduino or raspberry pi programmer for programming a ventilator

₹12500-37500 INR

Stengt

Lagt ut

over 2 år siden

₹12500-37500 INR

Betalt ved levering

The project is ventilator. Make a program which can run all of the components forming a feedback in such a way that when we open or close the solenoid valves using relays they will provide us with required proportion of oxygen in the air. the normal air contains 21% of oxygen and oxygen from gas cylinder contains 100% of oxygen so you have to turn off or turn on the solenoids so that they can provide us with a desired concentration of oxygen in the mixed air from both inlets. oxygen sensor is followed with other sensors which are barometric sensor ,pressure sensors etc. ( details of components and working is given in the document attached) . this is kind of overview if you can help me then i can provide you with more information and i have other alternates for mixing of oxygen and air if you find this solenoid method difficult. please help me if you can provide me with a working software for my project. I`ll be thankful to you if you accept my work. you can take 6-8 days for completing the work. for more information you can contact me anytime

Prosjekt-ID: 31821380

Om prosjektet

13 forslag

Eksternt prosjekt

Aktiv 2 år siden

Ønsker du å tjene penger?

E-postadresse

Fordeler med budgivning på Freelancer

Angi budsjettet og tidsrammen

Få betalt for arbeidet ditt

Skisser forslaget ditt

Det er gratis å registrere seg og by på jobber

13 frilansere byr i gjennomsnitt ₹25 077 INR for denne jobben

@sagradoamicus

Hi, I am arduino expert. I have almost 13 years of experience. I have read the details and have a few questions. Please get back to me to discuss it further. Thanks

₹25 000 INR om 7 dager

4,8

(223 omtaler)

7,8

@elect2eng

Hello, I can create a program using Arduino or other microcontroller , if you could send me the logic and the datasheets of the sensors. Do you have a circuit diagram or is it to be generated. We need to see if relay operation would produce the desired results depends on the range in which the oxygen % in the air+oxygen mixture. If you have a proportional valve it might give a better result. Please come on line to chat.

₹25 000 INR om 7 dager

5,0

(53 omtaler)

5,3

@mdjavedakhtar

hi there i have 13+ years of experience in Automation software i can use the solenoid design and oxygen level sensor to adjust the oxygen flow you have mentioned attachment but nothig there in the project details plz msg to discuss in detail.

₹20 000 INR om 7 dager

4,8

(28 omtaler)

5,2

@sivom

Can you please share more details of what you exactly need? Can you provide an block diagram of your system? What you have done so far? and what you expecting from the freelancer? What all the components used? Do you have the hardware ready? You want only programming support? We can discuss Regards Senthil

₹40 000 INR om 30 dager

5,0

(15 omtaler)

5,0

@LuisR1412

I am a python, C #, arduino, esp32, esp8266 programmer and I have done a large number of projects, already read your requirements and I can help you, am at your service

₹18 000 INR om 7 dager

5,0

(6 omtaler)

4,4

@sajjadtaghvaeifr

Hi, I hope you are doing fine. I am an expert in C programming, Microcontroller (AVR, ARM and etc), Arduino and Python.I have done some simulation and testing various type of Microcontrollers and sensors. I have experience work with Arduino including NANO, MEGA and etc. I'm interested in your project. Please send me a message so that we can discuss more. Best regards.

₹25 000 INR om 7 dager

4,6

(13 omtaler)

5,0

@edi45

Hi I have 8 years of experience in embedded system, and i might be able to help you. I didn't see attachment file, so if you can share it with me, we can get started

₹25 000 INR om 7 dager

5,0

(13 omtaler)

4,6

@EmbeddedAToZ

Dear client, I can help you complete the ventilator project. I have experience in developing commercial products such as vending machines, incubator controller's, sanitizer dispenser, air purifier, etc. I am an embedded developer with more than 4 years of experience. We can use either arduino or raspberry pi for this project. But I suggest using Arduino with AVR programming. Since the raspberry pi uses memory card for storing program, it may get currupt and device will stop working. Since this is a medical equipment, I prefer using AVR programming instead of Arduino IDE. Let's chat so that we can discuss further.

₹20 000 INR om 8 dager

5,0

(3 omtaler)

2,9

@IvanCNali

Hello, reading your project details I understand that you have solenoid valves, an oxygen sensor, barometric sensor, pressure sensor and others. The type of each sensor is important to determinate the communication between the sensors and the microprocessor, that can be analog or digital, all can be made. I would like to help, let's work in your project.

₹30 000 INR om 7 dager

5,0

(1 omtale)

2,7

@parmaraditya4497

Hello there, I have experience in building ventilator , In start of pandemic I worked on making ventilator. I have worked on software of ventilator using arm7 microcontroller. I know how we can control the proportion of oxygen and inhale exhale rate and many different functions. I can do this task efficiently. I can guide you until the product level. Lets discuss more in chat... Regards Aditya singh parmar

₹33 000 INR om 14 dager

5,0

(3 omtaler)

2,3

@gustavoruza

Hi, I do not see a file attached to your project publication, I work both with Arduino and with Schneider Electric brand PLCs, I would like to know what type of devices are you considering for the control system, when you talk about solenoid valves you do not specify what type They are, if they are motorized, adjustable position, On-Off, likewise the sensors you use if they have a normalized electrical output or send the reading by communication protocol, in short there are many ways to do a control, I need more information to be able to help you .

₹40 000 INR om 7 dager