time o'clock rememberers

Avbrutt Lagt ut 5 år siden Betales ved levering
Avbrutt Betales ved levering

I have a box, it has 8 drawers, each drawer has:

• One LED light, this LED will glow each time when the patient has to take the medicine in this specific drawer.

• One microswitch, it’s an endstop switch, this switch will go high and trigger a signal when the patient opens the corresponding drawer, the drawer will mechanically activate this switch exactly as a microwave door.

Arduino content

In Arduino code, there will be 8 variables (drowers), and each drower contain a specific medicine, this configuration must be editable via arduíno local or via internet. Via Internet is enough.

The drower content is as follows:

Drower 1 contains ----------metformina 850mg

Drower 2 contains ----------glibenclamida 5mg

Drower 3 contains ---------AAS 100MG

Drower 4 contains ---------enalapril 10mg

Drower 5 contains ---------losartana 50mg

Drower 6 contains ---------fluoxetina 20mg

Drower 7 contains ---------sinvastatina 20mg

Drower 8 contains ---------paracetamol 500mg

Indications

Metformina 850mg (drower 1) must be taken each 12h hours, this means that Arduino will play an alarm(piezzo buz), and will glow only the LED of the drower number 1. And if there is another medicine that must be talking at the same time, Arduino will glow that LED too.

The piezo and the LED will remain active(ringing a D glowing respectively) until the patient opens that drower or drowers, once he opens the drower this will -------activate switch, it means the microswitch will go high, and Arduino will receive the signal and it will do the following:

1-it will stop the alarm of the piezzo and turn of the LED.

2-ut will send a signal to iot site and let him know that this medication has been taking correctly

3-if the patient didn’t open the drower (take his medicine) at the time he should, Arduino will wait for only 45 minutes, if he doesn’t open the drower, Arduino will register and send messages to the iot site telling it that this medication was supposed to be taken at 8:00am but it wasn’t.

4-if the patient opens the drower (take his medicine ) after these 45 minutes (late) Arduino will send a message to the iot site telling it it was taking late, and at what time, and after how many minutes.(for example, if he took the medication (opens the drower) at 9:00am, Arduino will say patients is 1 hour late. This information will be ponderable and will drow a chart showing how many time he misses the medication hour.

Now in the iot site

I want to see a forms so I can input the medication and determine Wich medication is inside of Wich drower.

For example:

In Form number one one I’ll put Metformina 850mg, beside this form there is another one where I’ll input the frequency, for example each 12 hours.(so we need a button to creat a form, in Wich we input the medication and the frequency in Wich will be taking. When finished, just click on New medication and so on.

The iot site will show me daily, weekly, monthly and yearly report, informing or showing a chart and the amount of adherence of the patient to the medical indications (taking the pills correctly)

Each time the patient Misses a pill,(more than 45 minilate) the iot will send an email and and message to a predetermined number saying “the patient didn’t take the 8:00am pill. So the familiar member will call him .

C-programmering C++ Programmering Programvarearkitektur

Prosjekt-ID: #18632301

Om prosjektet

8 bud Eksternt prosjekt Aktiv 5 år siden

8 frilansere byr i gjennomsnitt $60 for denne jobben

kcbStar

Hello, I have experience in C/C++ programming. Please give me the descriptions of the project. Please let me know about your project. thank you.

$35 USD på 1 dag
(130 Omtaler)
6.4
TalAkerele

Hi, I am very happy to bid your project. I read your requirements carefully,so i see what you mean. I have been experiments with C Programming, C++ Programming, Software Architecture I'd like to work with you. i'l Mer

$20 USD på 1 dag
(48 Omtaler)
5.6
grigorywazin

Hi. I am a Senior Software Engineer with 8+ years' rich experience. I have very strong skills in C/C++, C#, .NET, Java and x86/x64 Assembler. If you desire the best qualified result in your project, you should choose Mer

$111 USD på 2 dager
(9 Omtaler)
5.3
andyf1

Good day! I am interested in working on your project. Please contact me so that we can discuss the details of your project. Look forward to your answer. Best regards.

$100 USD på 5 dager
(3 Omtaler)
1.3
amit45pj

I have worked on micro controller with c and application development with c++ . Even worked on the GUI based application.

$25 USD på 1 dag
(0 Omtaler)
0.0
engrahsen

I have prior experience of software programming

$30 USD på 10 dager
(0 Omtaler)
0.0