PLC RSLogix programmer for a small school work

Lukket Lagt ut 6 år siden Betales ved levering
Lukket Betales ved levering

Develop a control system for an automated garage door opener. You have been assigned the responsibility to develop the sequence of activities that are needed to successfully operate the garage door opener and to prepare a PLC program to monitor and control these activities. Details of the operations of the garage system are shown as follows.

develop the corresponding logic control programming code for the following operations and realize them by using the RSLogix programming software. The various activities involved in the operation of a garage door control system include the following:

The garage door is opened or closed using push-button switches X1, or remote control X2 and X3.

Depressing X1, X2, or X3 will open the garage door if it is closed, or close it if it is open.

To open the garage door, the opener motor should turn counter-clockwise (i.e., output Y1 is activated).

To close the garage door, the motor should turn clockwise (i.e., output Y2 is activated).

Energizing outputs Y1 and Y2 simultaneously will stall the opener motor and therefore they should NOT be simultaneously activated.

There are two limit switches that indicate fully open (X4) or fully closed (X5) status of the door.

The two limit switches (X4 and X5) are also used to stop the motor while closing or opening.

Excess load on the motor (while running) is detected by input X6.

The garage door reverses its direction upon detecting an overload (X6).

The garage light (output Y3) will go ON and stay ON when the garage door is being opened or closed. The garage light Y3 will remains ON until 10 seconds after the completion of the garage door-opening or the door-closing process.

A photo-sensor (X7) is used to detect obstacles during garage door closing (only). During the garage door-closing, if an object passes the door to trigger the photo- sensor X7, it will reverse the closing of the garage door and also sounds an alarm (output Y4).

Using RSLogix, develop the corresponding programming code for the mentioned operations of the garage door control system and realize them in the RSLogix programming software:

(Note: for defining the timer, create a tag and select timer as the data type. When the timer finishes timing, the output is [login to view URL])

PLC & SCADA

Prosjekt-ID: #15497170

Om prosjektet

18 bud Eksternt prosjekt Aktiv 6 år siden

18 frilansere byr i gjennomsnitt $112 for denne jobben

vadymosadchuk

A proposal has not yet been provided

$100 USD på 1 dag
(27 Omtaler)
5.5
vasiraj007

I have done a lot of University projects and industrial projects in RsLogix.. Interested in this project.

$222 USD på 10 dager
(19 Omtaler)
5.1
Jaynam254

I have very good work experience in RSLOGIX programming. I can develop your program in one day and i will be available for troubleshooting if required. I have license for all the RsLogix software. Please let me know wh Mer

$50 USD på 1 dag
(1 anmeldelse)
3.4
AbdullahSabir99

I understand your requirement, I can do this project. I'm expert Automation Engineer have done many projects related to PLC, DCS, HMI & SCADA based complex system, using multiple brands. I also have experience on allen Mer

$180 USD på 3 dager
(2 Omtaler)
3.1
mzlst50

hello, this is Dr yasser PLC,hmi, and scada system design and programming. please see the completed projects and clients review in my profile Relevant Skills and Experience PLC all brands including RSLOGix, hmi and sc Mer

$155 USD på 3 dager
(6 Omtaler)
2.4
nguyenges

A proposal has not yet been provided

$166 USD på 7 dager
(2 Omtaler)
1.5
mohamed593

Welcome, I hope you are well. I am interested in applying for this job which i good for its requirements. I am an electrical engineer. i have more than one year experience in plc programming . Relevant Skills and Exp Mer

$60 USD på 1 dag
(0 Omtaler)
0.0
hsood

A proposal has not yet been provided

$111 USD på 3 dager
(0 Omtaler)
0.0
Mahmoudoth

Dear, firstly this should be more precise what AB PLC are you using? and accordingly which revision of RSLogix you will be used? the type of I/Os? bases on these info a good proposal can be developed. Regards,

$111 USD på 4 dager
(0 Omtaler)
0.0
okkieleroux1

Hi. I am a PLC / SCADA professional. I can do this for you, probably in 1 day. It is very easy and I can comment the code so that you can understand it and learn from the program. Kind Regards. Relevant Skills and Mer

$100 USD på 5 dager
(0 Omtaler)
0.0
RBonamy

Hi, I'm new on freelancer.com, and I'm trying to get some reviews. About your project, I actually have a working "Two-way motor control" project on TIA Portal, and I used RSLogix for a year Thanks. Relevant Skills and Mer

$55 USD på 4 dager
(0 Omtaler)
0.0
sfareed11

A proposal has not yet been provided

$111 USD på 2 dager
(0 Omtaler)
0.0
denisnyambane

A proposal has not yet been provided

$133 USD på 4 dager
(0 Omtaler)
0.0